Categories
DIY Upcycling Ways With Wood

Tutorial – Image Transfers on Wood Jewelry

Tutorial – Image Transfers on Wood Jewelry

by Carolyn Hasenfratz Winkelmann

Materials

Thin wood scraps (about 1/8 – 1/4 inch thick)*
Gold acrylic paint*
White acrylic paint*
Large thin jump rings
Necklace chain with clasp
Cutout images from magazines or laser jet prints
Clear heavy-duty packing tape*
Scotch Magic Tape*
Clear-drying gel medium (several brands will work, including Modge Podge sold at the Schnarr’s Ladue store)
Paper towels*

Tools

Saw*
Drill with small drill bit*
Paint brushes*
Water container*
Sandpaper*
Clear plastic tote lid (or some other piece of rigid clear plastic like a piece of plexiglass)
Scissors*
Bone folder or burnisher
Basin for water*
Needle tool

* – indicates items sold at Schnarr’s

Instructions

1. Gather some thin wood scraps and cut them into pieces in the 3/4 inch to 2 3/4 inch range to make bases for wood pendants. Try different proportions and shapes so you can try out different design options.

2. Drill holes so the pendants can be strung onto a necklace later. You can also add extra holes for dangles if you want to. Sand the wood pieces smooth and wipe off with a damp rag.

3. Paint the wood pieces all over with gold acrylic paint. When the gold paint is dry, choose a spot on the front of your pendant and paint a white mark, such a stripe or a circle and let dry. When you start layering translucent images onto your pendant, the white spots will show through and help provide a focal point for your design. You can paint in a loose manner or make precise shapes or preferably experiment with both to see the effects.

4. Take some of your found images from magazines or laser prints and paint them with a layer of clear gel medium. Let dry, and apply a second coat with the brush strokes in the other direction. Let second layer dry, and apply a third coat in a diagonal direction. Let all layers dry for several hours.

5. Take strips of clear packing tape and use the Scotch Magic Tape to hold them down at the ends, sticky side up, on a rigid clear tote lid or piece of plexiglass. Cut or tear found images and press onto the tape pieces with the sides you want to show facing downward. As you layer on images, you can check your work by picking up the clear tote lid and peering from underneath to see what your work looks like.

The backs of packing tape pieces all filled with images.
The backs of packing tape pieces all filled with images.
The underside of the plastic lid showing tape pieces from the front.
The underside of the plastic lid showing tape pieces from the front.

6. After the tape is completely filled, remove from the lid and tape face down on a clean rigid surface like a desk top or table top. Rub well in several directions with a burnisher or bone folder.

Here are some tools you can use to burnish the images firmly onto the tape - bone folder, squeegee, French curve, old gift card.
Here are some tools you can use to burnish the images firmly onto the tape – bone folder, squeegee, French curve, old gift card.

7. After the tape strips are thoroughly burnished, soak them in water. Add the images that you coated with gel medium also. When the paper on the back gets soft, gently rub it until it peels away. You will probably have to change the water and rub multiple times to get all the paper off. When you are done, only the ink will be left on the tape. Dry the tape and gel pieces back/sticky side up on paper towels.

Tip – to avoid clogging your drain, dump the water with paper pulp in it outside instead of putting it down the drain.

8. Take one of your images on tape and hold it over your pendant piece until you find a composition you like. Loosely trim the tape piece and coat the front of the pendant with gel medium. Press the tape onto the front of your pendant and push any extra glue out and wipe off. Let dry, then trim around with a scissors. Use a crafting heat tool to speed the drying if necessary.

9. If your first image layer does not quite look finished as is, cut sections out of some of your gel-coated pieces and use the gel medium to glue them on top of your tape layer for extra interest. Top off with a final coat of gel medium and let dry.

10. Re-pierce your hole or holes with a needle tool, and put a jump ring in your hanging hole. If your pendant has multiple holes for dangles, put a jump ring in each hole and attach dangles to the jump rings. Run a jewelry chain with a clasp through the hanging jump ring. You are done!

More information

Here is another tutorial I wrote that makes use of image transfers:
Art Journaling With Stencils and Image Transfers

I have a Pinterest board for Image Transfer ideas and inspiration to help you explore further:
https://www.pinterest.com/chasenfratz/image-transfers/

If you would like to see what other classes and events I have coming up, please see this page on my blog:
http://www.chasenfratz.com/wp/about/classes-and-events/

Categories
DIY Upcycling Ways With Wood

Class at Schnarr’s Hardware this Thursday – Image Transfers on Wood Jewelry

Class at Schnarr’s Hardware this Thursday – Image Transfers on Wood Jewelry

by Carolyn Hasenfratz Winkelmann

 Image Transfers on Wood Jewelry
Class by Carolyn Hasenfratz Winkelmann – Image Transfers on Wood Jewelry

Date:
April 25, 2019

Time:
5:30-7:30 PM

Place:
Schnarr’s Hardware, 40 East Lockwood, Webster Groves, MO 63119

Schnarr’s employee Carolyn Hasenfratz Winkelmann is teaching this class again for the first time in three years, and for the first time at Schnarr’s. Make amazing lightweight pendants by transferring found images onto wood. You will be supplied with the materials to make a necklace for wearing your pendants. You will learn the basics of transferring images with tape and gel medium and attaching a clasp to a cord necklace. I will have a selection of transferred images on hand for you to use at the beginning of the class, then while your pendant or pendants are drying, I’ll show you two different techniques for converting found images into beautiful embellishments to add to wood pendants and other art and craft items.

Each class attendee will receive a printout with a written tutorial for that class so if you forget anything we learned you can refer back to it later. Jewelry tools will be available to borrow during the class and some tools and supplies will be available to purchase if you want to continue working on your own.

At each class, there will be at least one door prize randomly awarded to an attendee – probably a craft supply item of some type that relates to the theme of the class. Past prizes have included a necklace kit, a polymer clay frame kit and a craft stencil. That’s my way of saying thank you for coming!

What to Bring
It’s not necessary to bring anything but it’s a good idea to wear old clothes in case there is a glue mishap. If you have found images on glossy papers like magazine or catalog cutouts, or laser printed copies, you can bring those as a source for images.

What’s Provided
I will provide wood pendant blanks, gel medium, images, packing tape, findings and parts for at least one necklace. I will have tools to borrow during class.

Only 20.00 per person!

LINK TO GET TICKETS:
https://dabble.co/rc/carolyn-hasenfratz-winkelmann

Categories
DIY Upcycling

Art Journaling With Stencils and Image Transfers

Art Journaling With Stencils and Image Transfers

by Carolyn Hasenfratz Winkelmann

Materials (* = items that are available at Schnarr’s)
Scrap mat board or chipboard
Book binding rings* available at Schnarr’s Webster Groves Location
Clean scrap paper
Tracing paper
Clear packing tape – wider strips are the most versatile
An assortment of found papers (pages from old books, magazine pictures, catalog pictures, laserprint copies, paint samples, etc.)
Assorted papers to use as pages – can be drawing papers, art papers or found papers from various sources.
Paper towels*

Tools
Paper cutter
Art stencils* available at Schnarr’s Webster Groves Location
Permanent* and other markers
Colored pencils
Gel pens
Glue sticks*
Hole punch
Scissors*
Pencil*
Ruler*
Masking tape* or painter’s tape* for holding papers and stencils in place while tracing and stenciling
Bone folder, burnishing tool or squeegee*
Basin* filled with water
Clear packing tape*

In case you missed my in-store demo during the Webster Groves Fall Art Walk in October 2018, this art journal book is what I was working on. I chose to work with a lot of abstract designs and random images to have fun with shapes and colors and not worry too much about content. When I was working on my demo, a customer asked what I was doing and I told him. He responded by saying, “I don’t have any kids”. Kids could do a book like this, but it’s fun for a person of any age who likes to experiment with visual media. I’m 51 and I can play with this stuff for hours! Coloring and playing is healthy for anyone to do.

Instructions:

To make the cover, cut two pieces of scrap mat board or chip board into 6″ by 6″ squares.

Punch two holes in each piece along one edge and link with binding rings.

From an assortment of your found papers, cut several pages 6″ x 6″. Using the cover piece as a template, trace circles on your inner pages to indicate where to punch the holes for the binding rings.

Here is a selection of potential pages cut from old books, posters and magazine ads.
Here is a selection of potential pages cut from old books, posters and magazine ads. You can use blank sheets of paper in your book, but it can be intimidating to start with a blank page. When you’re making altered art you can just build on what is there.

Using permanent markers, draw through some stencils to start some compositions on your pages. The stencils shown in the above sample are stencils that I cut myself. You can cut your own stencils or use pre-cut art stencils. It helps make your work more interesting if you vary the line weight of the markers. Add bits and pieces of collage papers if you are inspired to do so. Glue them down with a glue stick.

Here are a few more examples of two page spreads in progress.
Here are a few more examples of two page spreads in progress. I added paint sample strips to some of the pages to remind me to have fun with color.

Next start making some image transfers to add to your pages from packing tape. Use masking tape to hold strips of packing tape flat on your work surface, sticky side up. Start sticking papers you like to the tape, keeping in mind that the side that connects with the sticky side and faces down is the one that will show. The recommended sources of good papers for image transfers are glossy images from catalogs and magazines, and black and white or color images from a copier or laser printer. Areas that are white on the paper may turn out to be mostly clear or translucent depending on how much ink and clays and minerals are in the paper.

When you have covered the tape with images, turn the tape over and burnish well with a bone folder or squeegee. Burnish in at least three different directions and press hard to make sure all the paper areas make contact with the sticky tape. In the image below, the tape pieces in the center have had the paper removed already, and the strips on the sides still have the paper on the back.

After the tape strips are thoroughly burnished, soak them in water. When the paper on the back gets soft, gently rub it until it peels away. You will probably have to change the water and rub multiple times to get all the paper off. When you are done, only the ink will be left on the tape. Dry the tape pieces sticky side up on paper towels.

When your tape strips are dry, you can apply a glue stick to the sticky side and paste them in your book where you think they’ll harmonize with what you’ve already started. Continue to develop your pages further with coloring implements of your choice and more stenciling and collage if you choose. These little books make a great portable art activity if you carry them around with a selection of your favorite drawing and coloring tools. Here are some of my pages in various stages of completion.

Open the binding rings to insert your pages inside the covers in any order that you like. Decorate the book cover if you want. If you ever want to add new pages, you can just open the rings and insert them where you want them. I put a date on my pages when I consider them complete, and if I am really pleased with them I upload them to my Art Journaling Pinterest board. Have fun!

Categories
DIY Upcycling

Making Signage From Letter Stencils: Part 2

Making Signage From Letter Stencils: Part 2

by Carolyn Hasenfratz

Tools and Materials
*Indicates items available at Schnarr’s
Assorted scrap cardstock
X-Acto Knife and Blades
Self-healing cutting mat
*Letter stencils
*Pencil
*Acrylic paint
*Paintbrushes
Acrylic medium
Paint mixing containers
Foamcore
Architextures™ Parchment Rub-Ons by Canvas Corp – Build
Assorted decorative papers with hardware related motifs
Bone folder or burnisher
*Modge Podge (available at our Ladue store)
Scrap corrugated cardboard
*Burlap
Fabric scissors
Paper cutter
*Nuts and bolts
*Brads
*Washers
Old wood yardsticks
*Awl
Metal ruler
*Masking tape
*Mounting tape
*Wrenches

My design for in-store signage for use on an endcap at Schnarr’s Hardware store in Webster Groves, MO was influenced greatly by my love of stencils. I had recently used stencils to make signs for another store. I was happy with the results and eager to try similar lettering techniques with a different look.

I took a set of chipboard reusable letter stencils that I got from Schnarr’s and used them to trace letters for the words “DIY Classes” on pieces of scrap cardstock and thin chipboard. I cut out each letter by hand using an X-acto knife, metal ruler and self-healing cutting mat.

My next step was to give each letter piece a wash of white paint mixed with matte medium and water. After the paint was dry I used some rub-ons burnished with a bone folder to add hardware and building imagery over the white paint wash around the cutout letters. Then with a small brush I outlined the letters and edges with a painted-on line of non-watered down white paint.

I cut out pieces of black cardstock slightly larger than my letter pieces and placed one behind each to add a frame and make the letters stand out. With an awl I poked holes in the four corners of each letter piece and fastened the layers of paper together with brads, using a variety of washers from my stash here and there with some the brads for extra variety and interest.

After making my letters, I measured the space available for my sign and took stock of what materials I had on hand. I knew I wanted a lightweight sign that would harmonize with the vintage imagery in the rub-ons, look good with the store’s color scheme and suggest the types of mixed media techniques I teach in the DIY Classes I’m promoting.

I decided to decoupage paper imagery all over a piece of foamcore and paint over the paper pieces with a wash of red-brown paint so that the designs on the papers would show through and not be too dominant. Most of the paper I chose was by the company DCWV. I looked for paper designs with things on them like vintage letters and numbers, rulers, keys, hardware, aged wood and brick, clock faces, vintage machinery and the like. I used Modge Podge to glue the papers over the foamcore and I mixed matte medium with the paint to make a translucent wash.

The finished foamcore panel was a bit smaller than the space I needed to cover so I made a frame out of cardboard covered with burlap to mount it on. First I cut out 8 pieces of corrugated cardboard, 2 for each side of the frame for extra strength. I bound the pieces of cardboard together with masking tape then I covered the cardboard frame sides with burlap, securing the burlap with tape on the back side. I poked holes in the burlap covered pieces and in the front foamcore piece with an awl and I used nuts and bolts with washers to attach the layers together.

I laid out my letters on top of the cardboard/burlap/foamcore assembly and saw that the second line, “Classes” was a bit too wide to fit onto the foamcore and was going to have to overlap the burlap edges to fit. I decided to bolt on a couple of old yardsticks to provide a surface for attaching the second row of letters. This emergency adaptation turned out to be a happy accident because in my opinion the rulers added great interest to the design and looked terrific with the images and colors I was using.

My last step was to attach the letters to the sign with mounting tape. I love this stuff!

Stop by Schnarr’s Webster to see the finished sign. On the endcap below it you’ll find samples of projects for future classes I’ll be teaching along with assorted art and craft supplies, some offered at clearance prices!

Categories
DIY Home Decor Upcycling Ways With Wood

Make a Shadow Box from an Old Drawer

Make a Shadow Box from an Old Drawer

by Carolyn Hasenfratz

Tools and Materials
*indicates available at Schnarr’s Hardware
Salvaged old drawer
*Screwdrivers
*Sandpaper
*Dust Mask
*Rags
*Wood filler (optional)
*Burlap, canvas or other solid color fabric
*Corrugated cardboard
*Glue gun
*Hot glue sticks
*Paint
*Paint brushes
*Water and mixing containers for paint
Metal ruler
Self-healing cutting mat
*Utility knife and sharp blades
Pencil
*Hanging hardware
*Small nails
*Hammer
Strong masking tape
Fabric Scissors
*Modge Podge
Squeegee tool
Decorative paper
Memorabilia, collectibles or decorations to display in the box
Optional – heat tool to speed up drying

Instructions:

1. Remove the old hardware from the drawer. You may or may not want to put some of it back on the box later so set the aside for now.

2. Sand the drawer inside and out. This is to give the surface a good “tooth” for paint and glue to adhere to. Wear a dust mask while sanding because you never know what is in old, reused wood. Wipe off the dust with a damp rag.

3. Now it’s time to take a look at your box and think about what you want to display in it. Do you want to set it on a table top or hang it on the wall? What is the look of the room it’s going to be in? Do you want to match the colors or decor in the room? When you have the answers to those questions you can start designing. Here are some pictures of past shadow boxes I have made with descriptions of what I did to give you ideas: Crafts By Carolyn: Shadow Boxes.

I’m going to use my sample shadow box as table decor for my upcoming wedding reception and later I’ll hang it on a wall. So I’m going to give mine a base to stand on as well as hanging hardware on the back. I’m going to paint the inside and the outside of the box to go with my color scheme (navy, coral, lime green and white), add a padded background for pinning small photos, add paper accents to the outside edges of the box with decoupage.

4. If the hardware you removed from your drawer left holes or if there are any other holes or uneven spots in the wood that bother you, if you want you can use wood filler to disguise them before you paint. In my case I like the distressed look and it goes well with the casual nautical theme I’m using so I chose not to fill in any holes in my sample box.

5. Paint your box on all sides and all edges with the exception of the inside back which will be covered. If you are hanging the box on the wall you can also skip painting the back. I’m going to display mine in the round first so I will paint the back.

There are some good painting tips for a distressed piece of wood in my previous article Stencil a Sofa Shelf Made From Distressed Wood.

6. While your paint is drying, you can start to work on your cardboard and fabric background. First measure the opening in your box. Then cut two pieces of corrugated cardboard to that size using a metal ruler, utility knife and self healing cutting mat.

There are some good cutting safety tips in my previous article Introduction to Letterboxing – Part II – Making a Personal Logbook.

Make sure your paint is dry enough to handle, then slip your cardboard pieces into the box and press them to the back to make sure they fit ok. If they are a little too large, cut them down bit by bit until they fit. Allow for a tiny bit of extra room around the edge to accommodate the fabric wrapping.

7. Select a piece of fabric to wrap the front of your cardboard pieces. Lay one of the cardboard pieces down on the fabric and draw around it with pencil. Add another two inches allowance to each side and draw lines. This is so you have enough fabric to grab onto, pull, and tape. Cut out your fabric along the outer line you just drew.

8. Heat up your glue gun and get your masking tape ready. Put a few dots of hot glue between your two pieces of cardboard and press together. If any sides of your cardboard have printing on them, make sure the printing is toward the inside or the back or it might show through the fabric.

9. If I were not applying hot glue to join this back to the inside back of the box, I would not expect the masking tape to be able to do all of the heavy lifting here in keeping this fabric on the board in the long term, but along with a generous application of the hot glue it will be adequate.

Fold fabric over the back and tape down. Start in the middle of each side and pull in the opposite side as you go and work your way out, pulling tight as you go.

10. You’ll want your hot glue gun nice and hot for this next step so a lot comes out. Apply a generous amount of hot glue around the inside back edge of the box and a little bit in the middle. Press the fabric-wrapped cardboard in good side up and hold for several seconds until the hot glue is holding it flat.

11. Apply decoupage decoration to the outside edges of the box if desired.

12. Attach hanging hardware or feet to the box with small nails.

Watch video of this project at Schnarr’s Hardware in Webster Groves:

Make a Shadow Box from an Old Drawer Part 1:

Make a Shadow Box from an Old Drawer Part 2:

Categories
DIY Home Decor Upcycling Ways With Wood

Upcoming Class at Schnarr’s: DIY Shadow Box on June 21

Upcoming Class at Schnarr’s: DIY Shadow Box on June 21

by Carolyn Hasenfratz

Learn how to make a shadow box from an old drawer
Learn how to make a shadow box from an old drawer

It’s easy to turn an old drawer from an unloved piece of furniture into an attractive and functional shadow box that fits your decor. Learn how from artist and designer Carolyn Hasenfratz at Schnarr’s Hardware in Webster Groves. Most materials are included, including the drawer. If you want metal feet on your box we have some along with some extra decorative hardware available for purchase.

What’s Provided
Drawers, fabric and board for backing, paint, essential hardware, glue, sandpaper, decorative papers

What You Can Expect

  • Learn how to make a functional background for tacking
  • Learn how to attach feet or hangers to your box for display
  • Get decorating and mounting ideas for your favorite keepsakes

Location
Schnarr’s Hardware – Webster Groves
40 East Lockwood Ave.,
St. Louis , MO , 63119

REGISTER HERE

Categories
Backyard Wildlife DIY Gardening Sustainability Upcycling Ways With Wood

Upcoming DIY Class at Schnarr’s: Build a Pollinator House on May 17


Three wood pollinator houses with stenciled decoration


Pollinator houses on display on endcap

As part of the series of DIY Classes at Schnarr’s Hardware in Webster Groves, Carolyn Hasenfratz will be teaching you how to make, decorate and fill a Pollinator House for your garden. Such houses are sometimes called Bee Houses or Bug Houses. They provide nesting and hibernating space for beneficial insects that bring life, color, pollinating services and natural pest control for your garden. We’ll have paint and stencils available for you to play with so you can give your house a personal touch.

Space in this class is limited to four people and the cost is only $20 per person including materials. Class time is 5:30 pm on May 17, 2018. Register now at this link:
Build a Pollinator House

If you can’t make it to the class, we have instructions for making two styles of pollinator houses published on the Schnarr’s blog:
Making a Pollinator House – Part 1
Making a Pollinator House – Part 2

Stop by Schnarr’s in Webster to see some of Carolyn’s prototype pollinator houses on display. These samples are for sale in case you’d prefer to buy one rather than make your own.

Categories
DIY Gardening Home Decor Upcycling Ways With Wood

Make a Wood Plant Tray

Make a Wood Plant Tray

by Carolyn Hasenfratz

Materials
*Indicates items available at Schnarr’s
*Piece of 1/2 inch thick wood cut to 4 inches by 13.5 inches (or other size of your choice)
*Wood for the sides of your planter (I used a variety of widths and thicknesses from my scrap pile plus the Schnarr’s scrap pile)
*Wood glue
*Nails
*Water putty
*Masking tape
*Paint
*3/16″ dowel rod
Ball knobs or drawer pulls with 3/16″ holes
*Disposable plastic gloves
*Dust mask for sanding

Tools
*Saw
*Pencil
*Ruler
*Hammer
*Putty knife
*Sandpaper
*Containers for water and mixing
*Paint brushes
Miter clamp
*Drill
*Small drill bit for pilot holes
*3/16″ drill bit
*Hand pruners
Old credit cards

Step 1: Cut a piece of wood that is 1/2 thick to 4 inches by 13.5 inches or to whatever size you want for the bottom piece of your plant tray. I actually used 1/4 inch thick wood in my sample because I had some lying around but you will have an easier time nailing it together if you use 1/2 inch thick wood.

Step 2: Decide where to cut the wood for the sides of the plant tray and mark the pieces with pencil. I made butt joints at the corners for this project so your wood pieces should be as long as the sides of the tray plus the thickness of the wood.

Parts for two wood plant trays
Parts for two wood plant trays

Step 3: Cut the side wood pieces to size and sand the rough edges.

Step 4: Dab on a little wood glue for extra hold as you arrange one of your butt joints in a miter clamp. We’re going to hammer a couple of nails in from the end to give more strength to the joint. Brace the clamped pieces in a vise as shown in my sample or on top of something like a large block of scrap wood. Drill a couple of pilot holes with a small drill bit. The pilot holes help the nail go in straighter and prevent the wood from splitting. Drive in a couple of nails and repeat until you have a three-sided frame assembled with one side open.

Wood pieces in a miter clamp
Wood pieces in a miter clamp

 

Miter clamp in a vise
Miter clamp in a vise

Step 5: Now we are going to put the bottom in our tray. Squirt some wood glue on the edges of your bottom piece and slide it into the frame. You can temporarily hold it in place with masking tape as you work. Put the last side on the frame and glue and nail the last two corners.

Step 6: Reinforce the bottom by driving a few nails into each side after drilling pilot holes.

Step 7: Next we’ll fill any cracks or holes with water putty. Since I tend to use a lot of scrap wood that has holes in it for my projects, I often patch the wood with spackling paste, water putty or wood filler. Then I can cover up the patches with paint, decoupage or some other surface treatment. I’m using water putty this time because I want my tray to be leak proof. Water putty dries really hard. In my sample I applied the water putty to the bottom of the tray as well as in the inside seams and anywhere else there were holes in the wood.

Mix a little but of water putty at a time with water until it’s a workable consistency. Put on disposable gloves and smear the putty it into the cracks and crevices you want to fill. Water putty is fairly hard to sand off so before it dries do a really good job of flattening and cleaning up the patches to reduce the amount of sanding you’ll have to do later. Old credit cards are a good tool for scraping away excess putty.

Step 8: After the putty sets up, sand your piece to get rid of rough edges. Wear a dust mask while sanding so you don’t breathe in the particles.

Step 9: Place your feet where you want them on the bottom of the tray and trace around them with pencil. I like to use ball knobs and drawer pulls with 3/16″ holes as feet on a variety of wood pieces. I keep a supply on hand along with 3/16″ pieces of dowel rod to use in joining the feet to the wood. After tracing, set the feet aside and drill a 3/16″ hole where each foot will go.

Step 10: Cut pieces of dowel rod to size so that they fit into the hole in the feet and into the holes you drilled in the bottom of the tray without leaving gaps. If you have a pair of hand pruners, I’ve found they do a quick and easy job cutting the dowel rod pieces to size. Put a dab of wood glue into each hole, push the dowel rod piece into the feet and then push the feet into the drilled holes.

Attaching the feet with wood pegs
Attaching the feet with wood pegs

When the putty is dry enough, your tray is ready to paint and decorate. Add some extra varnish to the inside of the tray to help make it waterproof for plant pots.

Categories
DIY Home Decor Upcycling Ways With Wood

Make a picture frame from scrap wood

Make a picture frame from scrap wood

by Carolyn Hasenfratz

Have you taken down an old fence or pulled up an old wood floor? Are you getting some remodeling done or have access to scrap wood? It’s fun to make reclaimed wood pieces into unique picture frames. For my sample I purposefully chose scrap wood with a rustic and weathered appearance, welcoming flaws that don’t compromise the wood’s structural integrity such as saw marks, knots, plaster stains and nail holes. This project is designed to exploit the unique qualities of scrap wood – the flaws in the wood are part of the “decoration”. If you like you can choose new wood and give the surface whatever treatment that fits your decor. You can even buy wood made specifically for picture framing if you want a more conventional style of frame. I made this frame the size of an 8 1/2 by 11″ award certificate because this is a common size that a lot of people need.

Watch Video of Carolyn Teaching this Class at Schnarr’s Hardware in Webster Groves:
Part 1
Part 2

Materials needed:
Scrap wood approximately the size of lattice strips – 1 1/2″ wide by 2/8″ thick. For my sample I used wood lath salvaged from a demolished building. You can purchase new lattice strips if you don’t have access to the right size scrap wood.
Scrap wood strips – 2/8 – 3/8″ thick by 1/2 – 3/4″ wide. I obtained my strips from the scrap stashes available to me. You can buy such wood new if you need to where molding is sold.
Small washers
Staples for staple gun
Sandpaper
Aluminum flashing
Small nails – long enough to go through both layers of wood but not long enough to penetrate to the front of the frame
8 1/2″ piece of plexiglass, clear acetate or glass
8 1/2″ piece of chipboard, cardboard or mat board
Wire
Wood glue

Tools needed:
Mitre saw
Eye protection
Staple gun
Dust mask
Drill with tiny drill bit
Ruler
Pencil
Permanent marker
Sturdy scissors
Wire cutter
Large nail
Scrap block of wood
Hammer
Staple gun

Click the diagram above to download a PDF copy to print out

1. The inside edge of the opening for your framed picture will be 8″ x 10 1/2″. When finished the frame will overlap the framed image about 1/4″ all the way around. Mark with a ruler and pencil on the wood where the cuts will be. You might find it helpful to draw a rough diagram on paper to help visualize the cuts. Using a miter saw, cut four wood pieces with 45 degree angles at the ends. Wear eye protection when sawing and drilling.

2. Sand the cut ends of the wood. I did not give my wood any other treatment or finish. This is partly because I like the way it looks as it is. Another reason is that this wood was salvaged from a historic building that has great personal significance to me. I did not want to alter the historic integrity of the wood beyond cutting it to size. There are saw marks on the wood from the 1920s which I think are cool! Salvaged lath wood that has been separated from its original historic context is often available for purchase at Perennial, an art studio that promotes the reuse of materials. If you want you can give your scrap or new wood further treatments such as sanding, painting or staining for a variety of decorative effects. Wear a dust mask while sanding – it’s never good to breathe dust and old wood may have mold spores or contaminants.

3. With a staple gun, shoot two or three staples into the back of the frame across each mitered corner. The staples will help tack your work in place until you can get some bracing installed on the back of the frame to make it more sturdy. Tap the staples with a hammer if they need a little extra help going all the way into the wood.

4. On the back of the frame, center an 8.5 x 11 piece of chipboard, cardboard or matt board and trace around it as a guide for placing narrow wood strips on the back for holding your protective layer (plexiglass, clear acetate or glass) and artwork.

5. To make the bracing, cut four pieces from the wood strips that are approximately 2/8 x 3/8 inches thick and 3/4 to 1/2 inches wide. The lengths you cut from with wood will be slightly different depending on how wide the strips are. Cut them so that the inside edge opening is 8 1/2 by 11. Make the lengths 9 inches for the short side and 11 1/2 inches for the long sides if using 1/2″ wide wood. If using 3/4 inch wide wood use 2 9 1/4″ pieces and 2 11 3/4″ pieces. If you are using wood in different dimensions just cut them so that the opening id 8 1/2 x 11″. Since you’ll be attaching these pieces to the back of the frame, if the pieces don’t all match or don’t line up perfectly it doesn’t matter, they won’t be visible. Sand pieces smooth.

6. Apply a line of wood glue on the back of each wood strip then press in place on the back of the frame. Drill small pilot holes, about three per strip, then nail the strips to the frame.

7. Next make some metal tabs to hold the artwork into the frame. These tabs are designed to swivel in and out so that you can easily take out or put in artwork. Draw four rectangles with permanent marker, 1 3/4 by 2 1/2 inches each, onto aluminum flashing. The flashing we sell has both a silver colored side and a brass colored side. These tabs won’t be visible when the frame is on the wall but if you have a preference for one side or the other keep that in mind. Using a sturdy pair of scissors cut out four pieces and round the corners to avoid sharp points. Sand or file the metal peices to get sharp edges off if necessary. On two of the pieces drill or punch one hole toward one end, on the two other pieces drill or punch a hole in each end. An easy way to punch a hole is to place the flashing on a scrap wood block and hammer in a large nail where you want the hole.

8. Attach the four flashing pieces to the back of your frame as shown on the diagram. Place a small washer under each nail head.

9. You are now ready to add artwork to the frame. First put in your clear protective layer (the glass, acetate or plexiglass), the display item, then a stiff layer of chipboard, cardboard or mat board to protect the artwork from the back and keep it from falling out. Rotate the tabs inward.

10. String a piece of wire from inner holes on the two-hole tabs from one side to the other for hanging. You’re done!

Here is how my frame looks with a certificate displayed in it:

Suggestions For Sources of Scrap Wood
Ask home improvement stores for scraps.
Volunteer to clean out someone’s garage or workshop in exchange for keeping some interesting wood pieces.
Make inquiries of people you know who are doing home improvements.
Look in thrift stores for picture frames or cheap pictures in frames that you can get parts from.
Make a request for wood pieces from the Freecycle community – freecycle.org
Walk your neighborhood on trash day – I’ve found so much usable wood that way.
Purchase salvaged supplies from a non-profit studio that specializes in reclaimed materials such as Perennial or Leftovers, Etc..

Categories
DIY Sustainability Upcycling

Decorate Gift Packages with Stencils and Chalk

Decorate Gift Packages with Stencils and Chalk

by Carolyn Hasenfratz

Decorate Gift Packages with Stencils and Chalk

In this tutorial I’ll show you how to make your own stencils from recycled food container lids and use them to decorate personalized gift packages. Many of the stencil designs I used in my demo were traced from nostalgic Christmas cookie cutters that were passed down to me from parents and grandparents. They bring back a lot of happy memories of doing holiday crafts and baking with my Mom. Most of the time making things in preparation for the Holiday was more fun for me than the actual event!

I designed this project to be something you can do with kids, but I think anyone who enjoys being a little bit playful and making eco-friendly packaging would enjoy this – I know that I had a great time!

Part 1 – Making the Stencils

Tools and Materials – *indicates available at Schnarr’s
Self-healing cutting mat
*X-acto knife or craft knife and blades
*Sharpie marker
Cookie cutters
*Pencil
Cleaned plastic food container lids
*Scissors

1. Take an old plastic food container lid and cut off the rim.

2. Choose a cookie cuttter or some other object to use as a template and trace around it with pencil on a piece of paper. Or if you have no such object, draw a simple shape of your choice.

3. Place the food lid piece over the drawing and trace the outline with a permanent marker. Cut out the shape with a craft knife, scissors, or some combination of the two.

 

Part 2 – Applying Chalkboard Paint to the Paper

Tools and Materials – *indicates available at Schnarr’s
*Kraft paper or the backs of recycled grocery bags
*Chalkboard paint
*Small sponges
*Painter’s tape or *masking tape
Cleaned plastic food container lids

1. If you are using the backs of recycled grocery bags, you can get a lot of the folds and wrinkles out of them first by ironing them between pieces of clean scrap paper. Spread paper down on your work surface and tape edges to hold in place.

2. Dab some chalkboard paint onto an old food lid and dip a small sponge into it. Place your stencil on the paper and tape down if necessary to hold it steady. Dab the sponge gently inside the cutout area and slowly apply the paint. Increase the amount of pressure and paint if necessary to get full coverage. If you apply the paint gently and gradually, you can avoid applying too much and having it bleed under the stencil.

Here I am stencling chalkboard paint onto the kraft paper. I recommend that you apply the chalk after wrapping the package, but in this demo I drew with chalk on some of the shapes while I was still stenciling so that people would see the possibilities of the chalkboard paint.

3. Lift stencil straight up to avoid smearing and repeat until the whole piece of paper is covered to your satisfaction. Let the paper dry.

4. Wrap the package after the paint is dry.

 

Part 3 – Adding More Decoration

Tools and Materials – *indicates available at Schnarr’s
Colored chalk
Stickers
*Markers
*Ribbon
*Baker’s twine or decorative string
*Bows
*Gift tags
Spray fixative (optional)

 

Here is a selection of wrapped boxes and decorating materials to give you an idea of how you can combine markers, stickers, ribbon, twine and tags with your chalked designs.

Tip: If your package is going to get handled a lot before presenting, you can spray your chalk work with spray fixative to protect it. Spray fixative is a product artists sometimes use to protect pencil, chalk, pastel and other media that might smear, and it is available at art supply stores.

Drawing with both markers and chalk is great fun!

 

On this sample, I sponged the chalkboard paint around a cutout star that was left over when I made a six-pointed star stencil. Combined with royal blue marker drawn through another stencil and light blue chalk I made a Hanukkah design.

Part 4 – Making Gift Tags

Tools and Materials – *indicates available at Schnarr’s
Scrap chipboard or cardstock
*Chalkboard paint
*Paintbrush
Stencils
*Scissors
*Pencil
*Ribbon
*Baker’s twine or decorative string
Hole punch
Spray fixative (optional)

It’s easy to make chalkboard gift tags to go along with your chalk-enhanced gift packages.

1. Paint some chalkboard paint onto one side of some scrap chipboard or card stock and let dry.

2. Use your stencils to trace shapes onto the unpainted side with pencil and cut out. You can make your tags tag-shaped or any other shape you like that fits your theme.

3. Punch a hole at the top of your tag and attach a piece of ribbon or twine using a lark’s head knot.

4. Use chalk to write on the tag and protect with spray fixative if necessary.