chalkboard paint – Schnarr's Blog

Make a Rustic Message Center

For this message center to hang on a wall I deliberately used rough lath wood instead of smoother wood stock. I wanted to simulate the look of a utilitarian crate that is getting re-used for another purpose. I bought a bundle of new lath wood so that I would have enough for teaching and samples. You can use scrap wood that you have salvaged if you prefer. Salvaged lath wood often has bits of plaster clinging to it which is very interesting if you like the distressed look. A good source for salvaged lath wood is Perennial, a creative re-use studio where I occasionally teach. On the TV show “American Pickers”, they often pick up items for re-use that have “just the right amount of Stank on it” as they say. I know what they are talking about – it’s one of the reasons I love to work with salvaged materials mixed with new. I use a dust mask when sanding any wood, especially salvaged wood because you don’t know what’s in it or where it’s been!

Materials
Lath wood
*Small wire nails and tacks – some of them can be decorative if you choose. Recommended sizes – 19 x 1/2″ and 19 x 3/4″ (Quantity approx. eighteen 1/2″ and six 3/4″)
*Small wood screws – 4 x 1/2″ (Quantity six)
*Small washers – #6 (Quantity six)
*Chalkboard Paint
*Chalkboard Contact Paper
*Clipboard Clip (available at Schnarr’s Webster)
*Wood glue
Scrap cardboard
*Optional – White acrylic paint

Tools
*Sandpaper
*Saw
*Ruler
*Pencil
*Drill
*Tiny Drill Bit
*File
*Rags
*Paint water container
*Paint brushes
*Small clamps
Block of old wood for bracing wood while drilling and nailing
*Dust mask
*Squeegee or bone folder
*Utility knife, self healing cutting mat and *metal ruler, or paper cutter for cutting cardboard
*Phillips screwdriver
*Optional – small container for mixing paint wash
*indicates products available at Schnarr’s

Instructions

1. Cut 1 1/2 inch lath wood into the following lengths:

Four pieces – 15″
Five pieces – 6″
Two pieces – 1.5″

Use the pencil and ruler to measure and mark wood pieces, then cut.

Optional: Paint all the wood pieces on all sides with a wash of white acrylic paint and allow to dry.

Pieces cut from lath wood — You will need to cut eleven pieces of wood for this project.

2. Sand the rough edges off of your wood pieces. You are probably wondering why I placed the step of sanding the wood pieces after painting instead of the other way around. The reason is it brings out the rustic look more because you’ll be removing some paint as you remove the rough spots on the wood.

3. Lay the four 15″ long pieces down on your work surface. Place one of the 6 inch strips about an inch and a half from the top. Add another right at the bottom of what will become the back of the message center. If it is helpful, draw a pencil line lengthwise on the wood to help you line up your nail holes. Draw little dots to show where the nail holes will go.

4. Squeeze a little wood glue on the backs of the wood cross pieces and clamp in place if you have trouble with the wood sliding around while you’re trying to work on it. If any wood glue squeezes out just wipe the excess off with a rag. Drill a little pilot hole for each nail. You don’t want the drill hole to go through all the way, it only needs to go in far enough to help the nail stay in place and to keep the wood from splitting at the surface as the nail goes in.

Hardware I used in this project - wire nails, wood screws washers and Clipboard Clips — Hardware I used in this project – wire nails, wood screws washers and Clipboard Clips

5. Hammer in your 1/2″ nails. If any poke through the front, file off the sharp parts.

Nailing wood slats to back to hold vertical wood pieces together

6. Now start to assemble the tray that will be attached to the bottom front of the message center. Prop up one of the two small one and a half inch pieces of wood up against a piece of scrap wood. A small section of a 2 x 4 is the perfect size (2 x 4s are not really 2″ x 4″ as you can see.) Add a dab of wood glue and place a 6 inch cross piece on top, butting up the edges together. Drill a couple of pilot holes and nail in place. Repeat for the other end.

7. Add another 6″ piece to the bottom of the box and nail in place after dabbing with wood glue, then nail the whole assembly to the bottom front of the message center with 3/4″ inch long nails. It helps to prop up the other end with the 2 x 4 piece while you are nailing through the back.

Making tray for the bottom of the message center.

8. Next make a small chalkboard for the middle front. Cut out a 5 1/2″ x 9″ piece of scrap cardboard and cover with chalkboard Contact paper. Cut the Contact paper slightly larger than the cardboard so that you can fold the edges over for a neat look. Burnish the paper with a squeegee tool to make a nice tight seal. Paint the front of the chalkboard over with chalkboard paint. (Unfortunately the Contact paper does not really take the chalk well enough by itself, but it makes an excellent base for the paint.) Let paint dry.

Cover a piece of scrap cardboard with contact paper, then paint over with chalkboard paint

9. Nail the last 6″ wood strip across the top front of the message center and glue and nail in place. Place the clipboard clip where you want it and make little pencil marks to indicate where to drill two holes for the screws to hold the clip on.

10. Drill the pilot holes then thread a washer on two screws and drive the screws in place.

11. Use a screw and washer on each corner of the chalkboard to attach in the middle front of the message center. You are done!

Attach the clipboard clip and you are done! — Attach the clipboard clip and chalkboard and you are done!

Do you want some more ideas for for things to make out of wood? Here is the Pinterest Board I made awhile ago that was the inspiration for this article:
Rustic Spring Ideas – this project isn’t only for spring of course, but I started working on it in February.

There are also some ideas for fun wood projects here on the Schnarr’s Pinterest site:
Ways With Wood

Decorate Gift Packages with Stencils and Chalk

by Carolyn Hasenfratz

Decorate Gift Packages with Stencils and Chalk

In this tutorial I’ll show you how to make your own stencils from recycled food container lids and use them to decorate personalized gift packages. Many of the stencil designs I used in my demo were traced from nostalgic Christmas cookie cutters that were passed down to me from parents and grandparents. They bring back a lot of happy memories of doing holiday crafts and baking with my Mom. Most of the time making things in preparation for the Holiday was more fun for me than the actual event!

I designed this project to be something you can do with kids, but I think anyone who enjoys being a little bit playful and making eco-friendly packaging would enjoy this – I know that I had a great time!

Part 1 – Making the Stencils

Tools and Materials – *indicates available at Schnarr’s
Self-healing cutting mat
*X-acto knife or craft knife and blades
*Sharpie marker
Cookie cutters
*Pencil
Cleaned plastic food container lids
*Scissors

1. Take an old plastic food container lid and cut off the rim.

2. Choose a cookie cuttter or some other object to use as a template and trace around it with pencil on a piece of paper. Or if you have no such object, draw a simple shape of your choice.

3. Place the food lid piece over the drawing and trace the outline with a permanent marker. Cut out the shape with a craft knife, scissors, or some combination of the two.

Part 2 – Applying Chalkboard Paint to the Paper

Tools and Materials – *indicates available at Schnarr’s
*Kraft paper or the backs of recycled grocery bags
*Chalkboard paint
*Small sponges
*Painter’s tape or *masking tape
Cleaned plastic food container lids

1. If you are using the backs of recycled grocery bags, you can get a lot of the folds and wrinkles out of them first by ironing them between pieces of clean scrap paper. Spread paper down on your work surface and tape edges to hold in place.

2. Dab some chalkboard paint onto an old food lid and dip a small sponge into it. Place your stencil on the paper and tape down if necessary to hold it steady. Dab the sponge gently inside the cutout area and slowly apply the paint. Increase the amount of pressure and paint if necessary to get full coverage. If you apply the paint gently and gradually, you can avoid applying too much and having it bleed under the stencil.

Here I am stencling chalkboard paint onto the kraft paper. I recommend that you apply the chalk after wrapping the package, but in this demo I drew with chalk on some of the shapes while I was still stenciling so that people would see the possibilities of the chalkboard paint.

3. Lift stencil straight up to avoid smearing and repeat until the whole piece of paper is covered to your satisfaction. Let the paper dry.

4. Wrap the package after the paint is dry.

Part 3 – Adding More Decoration

Tools and Materials – *indicates available at Schnarr’s
Colored chalk
Stickers
*Markers
*Ribbon
*Baker’s twine or decorative string
*Bows
*Gift tags
Spray fixative (optional)

Here is a selection of wrapped boxes and decorating materials to give you an idea of how you can combine markers, stickers, ribbon, twine and tags with your chalked designs.

Tip: If your package is going to get handled a lot before presenting, you can spray your chalk work with spray fixative to protect it. Spray fixative is a product artists sometimes use to protect pencil, chalk, pastel and other media that might smear, and it is available at art supply stores.

Drawing with both markers and chalk is great fun!

On this sample, I sponged the chalkboard paint around a cutout star that was left over when I made a six-pointed star stencil. Combined with royal blue marker drawn through another stencil and light blue chalk I made a Hanukkah design.

Part 4 – Making Gift Tags

Tools and Materials – *indicates available at Schnarr’s
Scrap chipboard or cardstock
*Chalkboard paint
*Paintbrush
Stencils
*Scissors
*Pencil
*Ribbon
*Baker’s twine or decorative string
Hole punch
Spray fixative (optional)

It’s easy to make chalkboard gift tags to go along with your chalk-enhanced gift packages.

1. Paint some chalkboard paint onto one side of some scrap chipboard or card stock and let dry.

2. Use your stencils to trace shapes onto the unpainted side with pencil and cut out. You can make your tags tag-shaped or any other shape you like that fits your theme.

3. Punch a hole at the top of your tag and attach a piece of ribbon or twine using a lark’s head knot.

4. Use chalk to write on the tag and protect with spray fixative if necessary.